Specifications are subject to change without notice
Warnings
IMPORTANT INFORMATION
PLEASE READ CAREFULLY
The following
and
information is supplied to you for your protection and to provide you with many
years of trouble free and safe operation of your product:
2EAD
ALL
INSTRUCTIONS PRIOR TO OPERATING REDUCER )NJURY TO PERSONNEL OR REDUCER FAILURE MAY BE CAUSED BY IMPROPER INSTALLATION MAINTENANCE
OR OPERATION
s
7RITTEN AUTHORIZATION FROM 2EGAL "ELOIT #ANADA IS REQUIRED TO OPERATE OR USE REDUCERS IN MAN LIFT OR PEOPLE MOVING DEVICES
s
#HECK TO MAKE CERTAIN APPLICATION DOES NOT EXCEED THE ALLOWABLE LOAD CAPACITIES PUBLISHED IN THE CURRENT CATALOGUE
s
"UYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING THE ADEQUACY OF THE PRODUCT FOR ANY AND ALL USES TO WHICH "UYER SHALL APPLY
THE PRODUCT 4HE APPLICATION BY "UYER SHALL NOT BE SUBJECT TO ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE
s
&OR SAFETY "UYER OR 5SER SHOULD PROVIDE PROTECTIVE GUARDS OVER ALL SHAFT EXTENSIONS AND ANY MOVING APPARATUS MOUNTED
THEREON 4HE 5SER IS RESPONSIBLE FOR CHECKING ALL APPLICABLE SAFETY CODES IN HIS AREA AND PROVIDING SUITABLE GUARDS &AILURE TO
DO SO MAY RESULT IN BODILY INJURY AND OR DAMAGE TO EQUIPMENT
s
(OT OIL AND REDUCERS CAN CAUSE SEVERE BURNS 5SE EXTREME CARE WHEN REMOVING LUBRICATION PLUGS AND VENTS
s
-AKE CERTAIN THAT THE POWER SUPPLY IS DISCONNECTED BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENTS ,OCK OUT THE
POWER SUPPLY AND TAG IT TO PREVENT UNEXPECTED APPLICATION OF POWER
s
2EDUCERS ARE NOT TO BE CONSIDERED FAIL SAFE OR SELF LOCKING DEVICES )F THESE FEATURES ARE REQUIRED A PROPERLY SIZED
INDEPENDENT HOLDING DEVICE SHOULD BE UTILIZED 2EDUCERS SHOULD NOT BE USED AS A BRAKE
s
!NY BRAKES THAT ARE USED IN CONJUNCTION WITH A REDUCER MUST BE SIZED OR POSITIONED IN SUCH A WAY SO AS TO NOT SUBJECT THE
REDUCER TO LOADS BEYOND THE CATALOGUE RATING
s
,IFTING SUPPORTS INCLUDING EYEBOLTS ARE TO BE USED FOR VERTICALLY LIFTING THE GEARBOX ONLY AND NO OTHER ASSOCIATED ATTACHMENTS
OR MOTORS
s
5SE OF AN OIL WITH AN %0 ADDITIVE ON UNITS WITH BACKSTOPS MAY PREVENT PROPER OPERATION OF THE BACKSTOP )NJURY TO PERSONNEL
DAMAGE TO THE REDUCER OR OTHER EQUIPMENT MAY RESULT
s
/VERHUNG LOADS SUBJECT SHAFT BEARINGS AND SHAFTS TO STRESS WHICH MAY CAUSE PREMATURE BEARING FAILURE AND OR SHAFT BREAKAGE
FROM BENDING FATIGUE IF NOT SIZED PROPERLY
s
4EST RUN UNIT TO VERIFY OPERATION )F THE UNIT TESTED IS A PROTOTYPE THAT UNIT MUST BE OF CURRENT PRODUCTION
s
)F THE SPEED REDUCER CANNOT BE LOCATED IN A CLEAR AND DRY AREA WITH ACCESS TO ADEQUATE COOLING AIR SUPPLY THEN PRECAUTIONS
MUST BE TAKEN TO AVOID THE INGESTION OF CONTAMINANTS SUCH AS WATER AND THE REDUCTION IN COOLING ABILITY DUE TO EXTERIOR
CONTAMINANTS
s
-OUNTING BOLTS SHOULD BE ROUTINELY CHECKED TO ENSURE THAT THE UNIT IS FIRMLY ANCHORED FOR PROPER OPERATION
)N THE EVENT OF THE RESALE OF ANY OF THE GOODS IN WHATEVER FORM 2ESELLERS "UYERS WILL INCLUDE THE FOLLOWING LANGUAGE IN A CONSPICUOUS PLACE AND IN
A CONSPICUOUS MANNER IN A WRITTEN AGREEMENT COVERING SUCH SALE
4HE MANUFACTURER MAKES NO WARRANTIES OR REPRESENTATIONS EXPRESS OR IMPLIED BY OPERATION OF LAW OR OTHERWISE AS TO THE
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE GOODS SOLD HEREUNDER "UYER ACKNOWLEDGES THAT IT ALONE HAS
DETERMINED THAT THE GOODS PURCHASED HEREUNDER WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE )N NO EVENT WILL THE
MANUFACTURER BE LIABLE FOR CONSEQUENTIAL INCIDENTAL OR OTHER DAMAGES %VEN IF THE REPAIR OR REPLACEMENT REMEDY SHALL BE DEEMED
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE UNDER 3ECTION
OF THE 5NIFORM #OMMERCIAL #ODE THE MANUFACTURER SHALL HAVE NO
LIABILITY TO "UYER FOR CONSEQUENTIAL DAMAGES
2ESELLERS "UYERS AGREE TO ALSO INCLUDE THIS ENTIRE DOCUMENT INCLUDING THE WARNINGS AND CAUTIONS ABOVE IN A CONSPICUOUS PLACE AND IN A
CONSPICUOUS MANNER IN WRITING TO INSTRUCT USERS ON THE SAFE USAGE OF THE PRODUCT
4HIS INFORMATION SHOULD BE READ TOGETHER WITH ALL OTHER PRINTED INFORMATION SUPPLIED BY 2EGAL "ELOIT #ANADA
MECHANICAL WARNINGS AND CAUTIONS
