Specifications are subject to change without notice
Gearmotors
*<Ê- , -Ê ÊUÊ "7Ê6" / Ê£Ó6®
* , Ê- /ÊUÊ/ 6ÊUÊ£°äÊ- ,6 Ê
/",
Over-
DIMENSIONS
F.L.
Gearmotor
Arm.
F.L. hung
Output Torque Input
Catalogue
Type &
Ratio
Volts Amps Load
P
X
XL
XH
RPM
(Lb.In.)
HP
Number
Frame
to 1
DC
DC (Lb.)
Inches
10
100
1
⁄
20
M1125213
PZ4-30
180
12
2.7 155
3.00 3.25 9.28 7.72
30
100
1
⁄
17
M1125214
PZ3-30
60
12
5.2 155
3.00 2.68 8.74 7.18
55
56
1
⁄
17
M1125215
PZ3-30
30
12
5.6 171
3.00 2.68 8.74 7.18
*<Ê- , -Ê ÊUÊ- ,Ê, /
* , Ê- /ÊUÊ/ 6ÊUÊ£°äÊ- ,6 Ê
/",
Over-
DIMENSIONS
F.L.
Gearmotor
Arm.
F.L. hung
Output Torque Input
Catalogue
Type &
Ratio
Volts Amps Load
P
X
XL
XH
RPM
(Lb.In.)
HP
Number
Frame
to 1
DC
DC (Lb.)
Inches
4
40
1
⁄
40
M1115002
PZ5-30A 450
90
0.46 155
3.00 3.25
9.28 7.72
4
40
1
⁄
40
M1125046
PZ5-30A 450 180 0.19 155
3.00 3.25
9.30 7.74
10 100
1
⁄
20
M1115001
PZ4-30E 180
90
0.54 155
3.00 3.25
9.28 7.72
10 100
1
⁄
20
M1125047
PZ4-30A 180 180 0.31 155
3.00 3.25
9.30 7.74
20 100
1
⁄
20
M1115000
PZ4-30E 90
90
0.54 155
3.00 3.25
9.28 7.72
20 100
1
⁄
20
M1125048
PZ4-30A 90
180 0.31 155
3.00 3.25
9.30 7.74
30 100
1
⁄
17
M1125002
PZ3-30B 60
90
0.80 155
3.00 2.68
8.74 7.18
30 100
1
⁄
17
M1125037
PZ3-30B 60
180 0.36 155
3.00 2.68
8.74 7.18
60
56
1
⁄
17
M1125003
PZ3-30B 30
90
0.80 171
3.00 2.68
8.74 7.18
60
56
1
⁄
17
M1125036
PZ3-30B 30
180 0.36 171
3.00 2.68
8.74 7.18
100 36
1
⁄
17
M1125004
PZ3-30B 18
90
0.80 171
3.00 2.68
8.74 7.18
100 36
1
⁄
17
M1125035
PZ3-30B 18
180 0.36 171
3.00 2.68
8.74 7.18
150 24
1
⁄
17
M1125005
PZ2-30B 12
90
0.80 180
3.00 2.40
8.46 6.90
150 24
1
⁄
17
M1125034
PZ2-30B 12
180 0.36 180
3.00 2.40
8.46 6.90
300 10
1
⁄
17
M1125006
PZ2-30B 6
90
0.80 180
3.00 2.40
8.46 6.90
300 10
1
⁄
17
M1125033
PZ2-30B 6
180 0.36 180
3.00 2.40
8.46 6.90
106
SUB-FHP DC GEARMOTORS
PARALLEL SHAFT GEARMOTORS
.900
Ref
SCR RATED:
10-100 In-Lbs Torque
LOW VOLTAGE:
36-100 In-Lbs Torque
Electrical
Specifications:
SCR Rated Gearmotors
Totally enclosed,
permanent magnet DC
gearmotors, performance
matched for continuous duty service
over a 60:1 speed range. All have constant torque
throughout the range when powered by a full-wave
unfiltered SCR-type adjustable speed control having
a typical form factor of 1.3 to 1.4.
Low Voltage Gearmotors
Totally enclosed, permanent magnet DC gearmotors,
performance matched for continuous duty. Motors
are designed for battery power or can be used with a
low voltage controller with form factor up to 1.05.
Mechanical Specifications:
Precision machined in-line steel gears, with a
first stage steel helical gear followed by spur-type
gears. Lubrication is permanent semi-fluid grease,
reducing possibility of leakage. Output shafts have
needle bearings for high load capacities. Shafts are
hardened steel.
Conduit box not included with motor.
Optional
conduit box and PZ gearmotor mounting bracket
shown on page 121.
Application Notes:
These gearmotors are designed for mounting at
any angle, but motor below the reducer should be
avoided to prevent leakage of lubricant into the motor
should the motor shaft seal fail.
The motor’s stall torque could exceed recommended
full load torques. If this service is anticipated, a
current limiting device should be used. This issue is
even more critical for low voltage motors, typically no
controller is used since motor connected directly to
battery, so some type of current limit or fusing should
be considered.
Overhung load capacities shown are at center of
output shaft.
Model PZ gearmotors have the same mounting
dimensions as Bodine model D and Z, Baldor/
Boehm, Bison 100 gearmotors, and a number of
Dayton gearmotors.
For additional information, see Bulletin 1830.
PZ SERIES - DC
CONDUIT BOX DIMENSIONS (IN.)
FRAME
XW
AB
H
L
30/31
2.63 3.47 1.90 3.13
GEARMOTOR CROSS REFERENCE
. . . . . . . Page 217
“L” BRACKET AND CONDUIT BOX
. . . . . . . . . . . . 121
SPEEDMASTER
®
CONTROLS
. . . . . . . . . . . . . . . . . 139
QUICK REFERENCE
