107
Specifications are subject to change without notice
Gearmotors
*ÎääÊ- , -Ê ÊUÊ- ,Ê, /
* , Ê- /ÊUÊ/ 6ÊUÊ£°äÊ- ,6 Ê
/",
Over-
DIMENSIONS
F.L.
Gearmotor
Arm.
F.L.
hung
Output Torque Input
Catalogue
Type &
Ratio
Volts Amps. Load
P
X
XL
XH
RPM (Lb.In.) HP
Number
Frame
to 1
DC
DC
(Lb.)
Inches
5
353
1
⁄
20
M1115024
P303-30E 336
90 0.54
565
3.00 3.54 10.07
8.57
9
268
1
⁄
20
M1115025
P303-30E 216
90 0.54
474
3.00 3.54 10.07
8.57
18 150
1
⁄
20
M1115026
P303-30E 103
90 0.54
385
3.00 3.54 10.07
8.57
20 140
1
⁄
20
M1125092
P303-31E
90
1800.31
370
3.11 3.54 10.07
8.57
24 280
1
⁄
8
M1125069
P303-31E
76
90 1.30
353
3.00 3.54 11.54 10.04
31 220
1
⁄
8
M1125070
P303-30E
58
90 1.30
327
3.00 3.54 11.54 10.04
31 220
1
⁄
8
M1125038
P303-30E
58
1800.66
327
3.00 3.54 11.54 10.04
34
82
1
⁄
20
M1115027
P303-30E
52
90 0.54
318
3.00 3.54 10.07
8.57
51 130
1
⁄
8
M1125071
P302-30E
35
90 1.30
277
3.00 3.54 11.54 10.04
51 130
1
⁄
8
M1125039
P302-30E
35
1800.66
277
3.00 3.54 11.54 10.04
51
55
1
⁄
20
M1115028
P302-30E
35
90 0.54
281
3.00 3.54 10.07
8.57
61 113
1
⁄
8
M1125072
P302-30E
29
90 1.30
267
3.11 3.54 11.54 10.04
60
45
1
⁄
20
M1125093
P302-31E
29
1800.31
267
3.00 3.54 10.07
8.57
94
77
1
⁄
8
M1125073
P302-30E
19
90 1.30
236
3.00 3.54 11.54 10.04
94
77
1
⁄
8
M1125040
P302-30E
19
1800.66
236
3.00 3.54 11.54 10.04
109 27
1
⁄
20
M1115029
P302-30E
16
90 0.54
224
3.00 3.54 10.07
8.57
106 27
1
⁄
20
M1125094
P302-31E
16
1800.31
224
3.11 3.54 10.07
8.57
167 43
1
⁄
8
M1125074
P302-30E
11
90 1.30
197
3.00 3.54 11.54 10.04
170 43
1
⁄
8
M1125041
P302-30E
11
1800.66
196
3.00 3.54 11.54 10.04
*ÎääÊ- , -Ê ÊUÊ "7Ê6" / Ê£Ó6®
* , Ê- /ÊUÊ/ 6ÊUÊ£°äÊ- ,6 Ê
/",
Over-
DIMENSIONS
F.L.
Gearmotor
Arm.
F.L.
hung
Output Torque Input
Catalogue
Type &
Ratio
Volts
Amps. Load
P
X
XL
XH
RPM (Lb.In.) HP
Number
Frame
to 1
DC
DC
(Lb.)
Inches
5
353
1
⁄
20
M1125217
P303-30
336
12
5.6
565
3.00 3.85 10.07 8.57
31
220
1
⁄
8
M1125218
P303-30
58
12
10.6 327
3.00 3.54 11.54 10.04
53
130
1
⁄
8
M1125219
P302-30
35
12
10.3 277
3.00 3.23 11.54 10.04
61
113
1
⁄
8
M1125220
P302-30
29
12
10.4 267
3.00 3.23 11.54 10.04
SUB-FHP DC GEARMOTORS
PARALLEL SHAFT GEARMOTORS
X
H
SCR RATED:
27-353 In-Lbs Torque
LOW VOLTAGE:
113-353 In-Lbs Torque
Electrical Specifications:
SCR Rated
Gearmotors
Totally enclosed,
permanent magnet
DC gearmotors,
performance matched
for continuous duty service
over a 60:1 speed range. All have
constant torque throughout the range when powered
by a full-wave unfiltered SCR-type adjustable speed
control having a typical form factor of 1.3 to 1.4.
Low Voltage Gearmotors
Totally enclosed, permanent magnet DC gearmotors,
performance matched for continuous duty. Motors are
designed for battery power or can be used with a low
voltage controller with form factor up to 1.05.
Mechanical Specifications:
Precision machined in-line steel gears, with a
first stage steel helical gear followed by spur-type
gears. Lubrication is permanent semi-fluid grease,
reducing possibility of leakage. Output shafts have
needle bearings for high load capacities. Shafts are
hardened steel.
Conduit box not included with motor.
Optional
conduit box shown on page 121.
Application Notes:
These gearmotors are designed for mounting at
any angle, but shaft up with motor below should be
avoided to prevent leakage of lubricant into the motor
should the motor’s shaft seal fail.
Overhung load capacities shown
are at center of output shaft.
The motor’s stall torque exceeds recommended full
load torques. A current limiting device such as an
SCR control should be used to prevent damage.
Model 300 gearmotors have the same mounting
dimensions as Bison’s 300 and many Dayton
gearmotors.
For additional information, see Bulletin 1830.
P300 SERIES
CONDUIT BOX DIMENSIONS (IN.)
FRAME
AF
XW
H
L
30/31
6.26 2.63 1.90 3.13
